Bright LED 2-in-1 Driving Light/Turn Signal Upgrades for Older Bikes (pair)
These 2-in-1 LED Driving Light/Turn Signal upgrades are the brightest, safest and simplest lighting solutions available. Designed specifically for earlier BMW motorcycles, this product fits right inside the front wheel OEM indicator housing - no need for brackets, drilling or clamping. A full fitting kit is included with all components labelled and coded, along with the required wiring instructions and circuit diagram. Full written instructions are also included.
- Added safety
- Designed to give a very high intensity light performance in all weathers
- Designed specifically for BMW bikes
- Fits neatly into the original housing
- No need for additional external fitting
- Designed to work with your bikeís electronics
- No need for brackets, drilling or clamping
- Adds ultra-minimal weight to your bike
- Takes just 30 minutes to an hour to fit
- Very easy to replace if you drop your bike
- More effective and more affordable than other options
- Low cost or expensive bike, this solution fits them all
Ultrabrights are manufactured in the USA and UK.
Combined in an intelligent electronic circuit board design, this innovative LED upgrade has 24 powerful automotive standard LEDs: 12 amazingly bright white LEDs for the driving lights and 12 ultra-orange amber LEDs for the turn signals.
When youíre riding, these Ultrabright 2-in-1 upgrades have white driving lights which are always on. Thatís until you need to tell other road users that youíre making a turn. Flick your turn signal on and the driving light goes out on the side you select and the equally bright LED amber turn signal lights up. Cancel your turn signal after the maneuver and the driving light comes back on. Switch to hazard lights and both flash amber.
The white LED driving lights are designed to come on with your ignition and stay on throughout your ride whether itís day or night, sunshine or rain Ė and you get extra bright turn signals too all contained within your original turn signal housing.
Designed specifically for BMW motorcycles, this is a clever, cost-effective alternative to fitting heavy, bulky, ugly bolt-on driving lights. With Ultrabrights 2-in-1 upgrades, you donít have to spoil the look of your bike to be safer on the road.
Each pack contains:
2x LED Driving Light/Turn Signal upgrades
2x wires marked 'Weiser' at one end and '3-in-1 at the other end.
1x relay. The relay takes power direct from the battery and switches it to your Weiser driving lights to ensure the CAN bus will not flag any faults.
1x wire marked 'Relay 87' at one end and '3-in-1' at the end. This wire will take 12v from the relay to join with item 1 to provide the power to your Weiser driving lights.
1x wire with fuse holder marked 'Relay 30' at one end and 'Battery +Ve' at the other. This is providing the +12v to the relay so that it can be switched to your driving lights when the ignition is on.
1x wire marked 'Bike Earth' at one end and 'Relay 85' at the other. This wire provides the -VE to the relay.
1x wire marked 'Relay 86' at one end and is unmarked at the other. This wire needs to connect the relay to a switched +12v supply that is only on when the ignition is on. If available, the bike parking light is an easy location to connect to, using the Posi-Tap (item 8) provided.
1x Posi-Twist connector
1x Posi-Tap connector
1x 5 amp fuse - do not fit any other value fuse.
5x tie wraps - use these to secure the wires you are installing as instructed.
2x locking keys for securing the turn signal housing.
These Ultrabrights are suitable for the following BMW bikes:
R1200GS (up to 2012)
R1200GS Adventure (up to 2012)
R1200R and Sport (up to 2014)
F650GS (2008 to 2012)
F800GS (up to 2012)
F800R (up to 2012)
F800S (up to 2012)
F800ST (up to 2012)
G650 Xcountry (2006 to 2009)
G650 Xmoto (2006 to 2009)
G650 Xchallenge (2006 to 2009)
K1200R (up to 2008)
K1200R Sport (up to 2008)
HP2 Megamoto (up to 2008)
HP2 Enduro (up to 2008)
HP2 Sport (up to 2008)